Confined Space Refresher Level 2
February 21, 2025 @ 7:30 am - 2:00 pm
$246Confined Space Standby (Refresher)
Upcoming Training
| Course Start Date | Time | Spaces | Cost | Enrol Myself | Enrol Someone Else | Corporate Booking |
| 21/02/2025 | 07:30 am - 02:00 pm | 7 | $246.00 |
Confined Space Standby (Refresher)
This course is designed for experienced personnel employed in operational roles entering and working in confined spaces including acting as a Standby and working with Permit Controls Systems. Students must hold ALL of the following Units to be eligible for this refresher course.
| Unit of Competency | Must have been trained within |
| RIIWHS202E Enter and work in confined spaces | 3 years |
| RIIRIS201E Conduct local risk control | 3 years |
| MSMPER200 Work in accordance with an issued permit | 3 years |
| MSMPER300 Issue work permits | 3 years |
| MSMPER202 Observe permit work | 3 years |
| MSMWHS217 Gas test atmospheres | 3 years |
| MSMWHS201 Conduct hazard analysis (Note: MSMWHS201 Conduct hazard analysis is a prerequisite to the unit MMSPER300 Issue work permits) |
3 years |
To book, contact us by email to [email protected] or call 1300 MAXWEL (1300 629 935). Note you will be required to provide your existing Statement of Attainment for confined space training prior to the course start date.
Course Name
Confined Space Standby (Refresher)
Course Description
This course is designed for experienced personnel employed in operational roles entering and working in confined spaces including acting as a Standby and working with Permit Controls Systems.
Units of Competency (Students must hold ALL of the following Units to be eligible for this refresher course)
- RIIWHS202E Enter and work in confined spaces
- RIIRIS201E Conduct local risk control
- MSMPER200 Work in accordance with an issued permit
- MSMPER300 Issue work permits
- MSMPER202 Observe permit work
- MSMWHS217 Gas test atmospheres
- MSMWHS201 Conduct hazard analysis
(Note: MSMWHS201 Conduct hazard analysis is a prerequisite to the unit MMSPER300 Issue work permits)
Entry Requirements
To be accepted into the program, applicants must provide evidence of successfully completing the current units of competency outlined above, in the last three (3) years. Evidence must be in the form of a nationally recognised qualification or statement of attainment.
Physical Requirements
Students must have the physical ability to complete the practical aspects of entering and working in confined spaces and associated tasks. Tasks may include but not limited to, climbing ladders whilst maintaining three (3) points of contact, being suspended in a full body harness and crawling through confined spaces.
Demonstrating Competency
On successful completion of the course, students will be issued with a Statement of Attainment recognised under the Australian Qualifications Framework. Students will receive recognition of refresher training for the units of competency they have been previously issued.
Course Content will cover
- Regulatory Framework
- Work Permit and Systems
- Work Control Systems
- Workplace safety procedures
- Risk Management
- Risk Control
- Isolations
- Gas Testing
- Standby Work
- Communications
- Entry and Exit Procedures
- End of day procedures
- Reporting and Recording procedure
Duration
One day (approximately 6.5 hours). Start time is 7.30am – finish time is approximately 2:00pm
Location of Training
Delivered at the Maxwell Training facility, 17 Callistemon Close, Warabrook NSW 2304
Maximum Student Numbers
8
Course Cost
The total cost is $246.00
Book Now
Prerequisites
MSMWHS201 Conduct Hazard analysis is a pre-requisite unit to MSMPER300 Issue Work Permits
Entry Requirements
Students are required to have the physical ability to successfully complete the practical aspects of entering and working in confined spaces and associated tasks. These may include, but are not limited to climbing ladders whilst maintaining three points of contact, donning and wearing a full body harness and being suspended in full body harness, entering and working in a confined space and manual handling
Language, Literacy and Numeracy
Due to previous successful completion of all units of competency offered in this program, completing a language literacy and numeracy assessment is optional. If you feel you would benefit from undertaking the LLN assessment before making a commitment to enrol, please contact the Training Coordinator on 1300 MAXWEL (1300 629 935)
Delivery Method
This course is delivered entirely face to face with a combination of theoretical and practical components.
Assessment Process
Assessment methods include:
Knowledge questions
Practical demonstration in a simulated environment
Completion of various workplace forms and documents
Students must provide
- Lunch
- Safety helmet with chin strap
- Safety gloves
- Long work pants (jeans are acceptable)
- long sleeved work shirt
- steel cap boots
Maxwell Training will provide
- All course material
- Safety Harnesses
- Tea and coffee facilities
- A lunch truck attends the training site daily
Award
Upon successful completion, students will be warded with a nationally recognised statement of attainment from Maxwell Training Pty Ltd.
Additional Student Information
- To view/download the Student Information Handbook, go to the Student Resources page
- To view/download the Complaints and Appeals Policy, go to the Student Resources page
- To view/download the Fee and Refund Policy, go to the Student Resources page
To view/download the Maxwell Training's Standard Terms and Conditions, go to the Student Resources page
Bookings/Enquiries
Please telephone us on 1300 MAXWEL (1300 629 935) for upcoming Course dates and for bookings.
